United States International Trade Commision Rulings And Harmonized Tariff Schedule
faqs.org  Rulings By Number  Rulings By Category  Tariff Numbers
faqs.org > Rulings and Tariffs Home > Rulings By Number > 1990 HQ Rulings > HQ 0544283 - HQ 0554945 > HQ 0554885

Previous Ruling Next Ruling



HQ 554885


February 23, 1990

CLA-2 CO:R:C:V 554885 GRV

CATEGORY: CLASSIFICATION

TARIFF NO.: 9802.00.80

Mark S. Zolno, Esq.
Katten Muchin & Zavis
525 West Monroe Street, Suite 1600
Chicago, Illinois 60606-3693

RE: Applicability of partial duty exemption under HTSUS subhead- ing 9802.00.80 to plastic connectors and blood cuff set sub- assemblies imported from Costa Rica

Dear Mr. Zolno:

This is in response to a letter of January 7, 1988, from your former law firm, Burditt, Bowles, Radzius & Ruberry, Ltd., on behalf of Baxter Healthcare Corp., requesting a ruling on the applicability of subheading 9802.00.80, Harmonized Tariff Schedule of the United States (HTSUS) (formerly item 807.00, Tariff Schedules of the United States (TSUS)), to plastic connectors and blood cuff set subassemblies imported from Costa Rica. Samples of each product were submitted for examination. You also request a ruling on the proper tariff classification of the connectors and blood cuff sets. You advise that your new firm, Katten Muchin & Zavis, has replaced the above firm as counsel for the importer in connection with this ruling request. We regret the delay in responding to your request.

FACTS:

You state that U.S. fabricated components, consisting of various molded plastic and rubber parts and vinyl tubing, will be exported to Costa Rica for assembly into plastic connectors and blood cuff set subassemblies. The plastic connector subassem- blies will be of two types, denominated 5-1 and duotherm pad connectors. To form the 5-1 connectors, several molded plastic parts will be sonic welded together into various configurations. To form the duotherm pad connectors, several molded plastic parts are joined together with holding fixtures. The connectors are then mechanically tested and visually inspected to ensure proper assembly and to detect leakage at the joints. The blood cuff assembly operation entails solvent sealing injection sites, caps and chambers to seven vinyl tubings of different lengths and diameters and attaching flow control devices, consisting of roller clamps, to the tubing. The blood cuff set is then similarly mechanically tested and visually inspected to ensure proper assembly.

You submit that both items are properly classifiable for duty purposes in TSUS item 709.27.

ISSUE:

Whether the operations performed abroad constitute accept- able "assembly" operations, thereby entitling the plastic connectors and blood cuff sets to the partial duty exemption under HTSUS subheading 9802.00.80 when returned to the U.S.

LAW AND ANALYSIS:

HTSUS subheading 9802.00.80 provides a partial duty exemp- tion for:

[a]rticles assembled abroad in whole or in part of fab- ricated components, the product of the United States, which (a) were exported in condition ready for assembly without further fabrication, (b) have not lost their physical identity in such articles by change in form, shape, or otherwise, and (c) have not been advanced in value or improved in condition abroad except by being assembled and except by operations incidental to the assembly process such as cleaning, lubricating, and painting.

An article entered under this tariff provision is subject to a duty upon the full value of the imported assembled article less the cost or value of the U.S. components assembled therein, pro- vided there has been compliance with the documentation require- ments of section 10.24, Customs Regulations (19 CFR 10.24).

"Assembly," for purposes of HTSUS subheading 9802.00.80, means the fitting or joining together of fabricated components. Acceptable assembly operations are interpreted at section 10.16(a), Customs Regulations (19 CFR 10.16(a)), which specifically enumerates welding, gluing and the use of fasteners as acceptable means of assembly. Further, assembly operations may be preceded, accompanied, or followed by operations of a minor nature which are incidental to the assembly process. See, 19 CFR 10.16(b).

In this case, the exported components are joined together by means of sonic welding, the use of holding fixtures, and solvent sealing. As these methods are clearly analogous to assembly operations enumerated in 19 CFR 10.16(a), the sonic welding, use of holding fixtures, and solvent sealing operations are deemed to constitute acceptable methods of assembly for purposes of HTSUS subheading 9802.00.80.

Regarding the testing of the products by mechanical means, certain incidental operations cannot always be provided for in advance. If the testing of the U.S. components is of a minor nature incidental to the assembly process, it is permitted even though it may result in the U.S. components being advanced in value or improved in condition. H.R. Rep. No. 342, 89th Congress, 1st Sess. 49 (1965). The mechanical testing of the assembled articles in this case appears to be of a minor nature incidental to assembly process and is permitted.

In Headquarters Ruling Letter 036704 (May 30, 1975), PVC flexible tubing, rubber connectors, metal cannulas, rubber needle hubs and flashball assembly components of U.S. origin were assem- bled abroad into intravenous administration sets and fenwall blood bags. We stated that if the component parts were exported in condition ready for assembly without further fabrication, allowances could be made under TSUS item 807.00 for the exported components. On examination of the submitted samples in the instant case, it appears that the U.S. components are exported in a condition ready for assembly without need of further fabrica- tion. Further, the assembly operations do not cause the compo- nents to lose their physical identity or advance their value or improve their condition, except by being assembled and testing operations incidental to the assembly process.

The returned articles are classifiable in HTSUS subheading 9018.90.7080, which provides for instruments and appliances used in medical, surgical, dental or veterinary sciences, other instruments and appliances and parts and accessories thereof, other, electro-medical instruments and appliances and parts and accessories thereof, other, other. This provision provides for a duty rate of 4.2%.

HOLDING:

On the basis of the information and samples submitted, as all the conditions of HTSUS subheading 9802.00.80 are satisfied, the imported connectors and blood cuff sets are eligible for the partial duty exemption available under this tariff provision when returned to the U.S., provided the documentary requirements of 19 CFR 10.24 are met.

Sincerely,

John Durant, Director
Commercial Rulings Division

Previous Ruling Next Ruling

See also: