United States International Trade Commision Rulings And Harmonized Tariff Schedule
faqs.org  Rulings By Number  Rulings By Category  Tariff Numbers
faqs.org > Rulings and Tariffs Home > Rulings By Number > 1990 HQ Rulings > HQ 0086383 - HQ 0086452 > HQ 0086409

Previous Ruling Next Ruling



HQ 086409


April 16, 1990

CLA-2 CO:R:C:G 086409 JMH

CATEGORY: CLASSIFICATION

TARIFF NO.: 8482.40.00, 8482.50.00

Mr. Michael O'Neill
O'Neill & Whitaker, Inc.
1809 Baltimore Ave.
Kansas City, MO 64108

RE: Needle roller bearings

Dear Mr. O'Neill:

Your December 19, 1989, request for a classification ruling under the Harmonized Tariff Schedule of the United States Annotated (HTSUSA) for certain needle roller bearings on behalf of Tilden Corporation has been referred to this office for a reply.

FACTS:

The article in question is a needle roller bearing, Part #ROW/K1603/32 (1603/32), to be imported from West Germany. Bearing 1603/32 has a roller diameter of 4.76 mm (3/16 inch). (1 inch = 25.4 mm). This bearing has a roller length of 50.8 mm (2 inches).

ISSUE:

Whether bearing 1603/32 is a "needle roller bearing" or an "other cylindrical roller bearings" within heading 8482, HTSUSA, which describes "Ball or roller bearings, and parts thereof..."

LAW AND ANALYSIS:

The classification of merchandise under the HTSUSA is governed by the General Rules of Interpretation (GRI's). GRI 1, HTSUSA, states in part that "for legal purposes, classification shall be determined according to the terms of the headings and any relative section or chapter notes and...according to the following provisions..."

The appropriate heading in this instance is heading 8482, HTSUSA. The terms of heading 8482 provides eo nomine for roller bearings. The headings describes "Ball or roller bearings, and parts thereof..." Thus, the only question remaining is the classification within the subheadings.

GRI 6, HTSUSA, one the GRI 1's "following provisions", provides that the same process used to determine the proper heading is also used to determine the appropriate subheading. There are two possible subheading classifications for the needle roller bearings in question, subheadings 8482.40.00 and 8482.50.00, HTSUSA. These subheadings describe

8482.40.00 Needle roller bearings...

8482.50.00 Other cylindrical roller bearings...

Initially, it would appear that bearing 1603/32 fits within subheading 8482.40.00. However, the Explanatory Notes to the HTSUSA furnish details for the subheadings. The Explanatory Notes are not dispositive, but are to be looked to for guidance in the proper interpretation of the HTSUSA. 54 Fed. Reg. 35127, 35128 (August 23, 1989). Explanatory Note 84.82 (C) states that needle roller bearings are "cylindrical rollers of a uniform diameter not exceeding 5 mm and having a length which is at least three times the diameter." (emphasis added) Explanatory Note 84.82 (C), Harmonized Commodity Description and Coding System (HCDCS), Vol. 3, p. 1324.

Bearing 1603/32 has a roller diameter of 4.76 mm. A roller length at least three times this size would equal 14.28 mm. The bearing in question has a length of 50.8 mm. It is the opinion of this office that the Explanatory Notes should be followed. Therefore, the roller bearing in question meets the terms of subheading 8482.40.00, since the roller length is at least three times the roller diameter.

Bearing 1603/32, because of its size, is properly classifiable within subheading 8482.40.00, as "...Needle roller bearings..."

HOLDING:

The needle roller bearing, Part #ROW/K1603/32 (1603/32), has a roller length greater than three times its roller diameter.

This length qualifies the bearing for classification within subheading 8482.40.00, as "Ball or roller bearings, and parts thereof...Needle roller bearings..."

Sincerely,

John Durant, Director
Commercial Rulings Division

Previous Ruling Next Ruling

See also: