Search the FAQ Archives

3 - A - B - C - D - E - F - G - H - I - J - K - L - M
N - O - P - Q - R - S - T - U - V - W - X - Y - Z
faqs.org - Internet FAQ Archives

Electrical Wiring FAQ (Part 1 of 2)
Section - What is the CEC? Where can I get a copy?

( Part1 - Part2 - Single Page )
[ Usenet FAQs | Web FAQs | Documents | RFC Index | Forum ]


Top Document: Electrical Wiring FAQ (Part 1 of 2)
Previous Document: What is the NEC? Where can I get a copy?
Next Document: Can I do my own wiring? Extra pointers?
See reader questions & answers on this topic! - Help others by sharing your knowledge

	The Canadian Standards Association is an organization made up
	of various government agencies, power utilities, insurance
	companies, electrical manufacturers and other organizations.
	The CSA publishes CSA Standard C22.1 which is updated every two
	or three years.  Each province adopts, with some amendments,
	this standard and publishes a province-specific code book.
	Since each province publishes its own slightly modified
	standard, it would be somewhat confusing to obtain the CSA
	standard itself.  In this FAQ, "CEC" really means the
	appropriate provincial standard.  In particular, this FAQ is
	derived from the Ontario Hydro Electrical Safety Code, 20th
	edition (1990).  Which is in turn based on CSA C22.1-1990 (16th
	edition).  While differences exist between the provinces, an
	attempt has been made to avoid specific-to-Ontario detail.

	The appropriate provincial code can be obtained from electrical
	inspection offices of your provincial power authority.  In
	Ontario, it's Ontario Hydro.  The Ontario Hydro book isn't
	overly fat.  It's about C$25, and includes mailed updates.  I
	hear that these standards are somewhat easier to read than the
	equivalent NEC publications.

	Don't bother asking in Quebec - DIY wiring is banned throughout
	the province.

User Contributions:

1
Dev
In a fire protection circuit, circuts are shown witha no example 6,8,4etc. what it mean?these circuits are connected between smode detector,junction box etc
2
kevin
My daughter dropped a small necklace behind her dresser. The necklace crossed a plug terminal and shorted the receptacle.
I bought a new receptacle and installed the same. I still have no power I suspect there could be a bigger problem,this is aluminum wiring.
I've killed the breaker and call an electrician but am curious as to what happened.P.s. there is a dimmer switch on the same circuit.
3
dennis
Regarding new construction wiring and running 12/2 and 14/3 wire in the same box.

I have multiple switches to lights. Ran 12/2 and 14/3 into switch box and inspector wrote correction needed.

What should I have done instead?

thank you
dennis
4
Robert
Does a grounding electrode facilitate the operation of a OCPD, to clear a ground fault ?
5
@dennis
Assuming you are installing two switches in a two switch box, you probably should have used 14/2 and 14/3 instead of replacing 14/2 with 12/2. If you are only installing one switch in a one switch box, you should only have one cable in the box.
6
P k
I prefer to use nothing smaller than12 awg /the smallest sized wire on a circuit determines the allowable ampacity
Ex: 15 amp-14awg. 12awg-20amp only rule for thumb other factors such as continuous load,heating and others if you do not know the safe NEC rules then please call a qualified journeyman Electrician better be safe

Comment about this article, ask questions, or add new information about this topic:




Top Document: Electrical Wiring FAQ (Part 1 of 2)
Previous Document: What is the NEC? Where can I get a copy?
Next Document: Can I do my own wiring? Extra pointers?

Part1 - Part2 - Single Page

[ Usenet FAQs | Web FAQs | Documents | RFC Index ]

Send corrections/additions to the FAQ Maintainer:
clewis@ferret.ocunix.on.ca (Chris Lewis)





Last Update March 27 2014 @ 02:11 PM